Interfacing The KPC3+
And The Davis Weather Station/APRS
01/23/06
This will make the KPC3+ into both a digi and weather station for APRS.
Items needed:
1.Kantronics KCP3+ [V9.1] TNC.......fused @1/2A
2.Davis
Weather Station, # 6152c,VantagePro2-Cabled, # 6540
Weatherlink-APRS, # 7720 Heater [ for ice in West Texas ]
3.Ericsson GE 344A4210P2 40W VHF [ radio ] /144.39 mhz / fuse 7.5A
[
fast t / r switching and efficent / 6 1/4A @ 40 watts ]
Cables:
1.Radio
cable to TNC / Db-9
Db-9/tnc to radio
1.Mic---------to mic
circuit
3.PTT--------to ptt
5.Rx----------disc [open sq.]
use circuit below [pl3 /pin3 GE ]
6.Gnd--------gnd
Cable pulled out of radio at
the SO-239.
Parts
c = .047 uf De-emphasis Circuit
cc = .15 uf GE db-9 to tnc
rrr = 6.8k ohms radio [ pl3 / pin 3]
>---cc----------rrr---------> pin 5
[disc.] |
c
|
gnd
2.Computer
to tnc cable
Db-9(computer) Db-25
(tnc)
2.Data in -------------------- 3. Data out
3.Data out ----------------- 2. Data in
5.gnd -----------------------
5. gnd
3.Db-25/tnc
to Davis comes with Davis # 6540
Db-25 [ on the KP3+ ] will be the computer hook-up and the Davis Weather
Station.
KPC3+ JUMPERS
J1 on batt. use 9v
J2 off batt use 9v
J3 off for 10k rx audio
J4 on no equal.
J7 off RESET
The rest of the jumpers can be left at factory settings.
KPC3+ [V9.1] Software Settings:[Use
hyperterm Windows @ 9600 baud 8/N/1]________
1.Restore / back to factory spec.[J7] * Set time,Daytime-' Da
mm/dd/yyyy hh:mm:ss'
2.Mycall: N5SOR-2 info : *
'?command'=help
3.Intface: TERMINAL *to get out of GPS mode :' ctrl c'
4.Cd : SOFTWARE [ for open SQ ] *set dev. to 3.25 khz
& use 'cal' &'+ / -' to adj. mod
5.Hid : OFF
6.Uidwait : OFF
7.Uiflood : TX,30,ID
8.Uitrace : WIDE,30
9.Uidigi : ON WIDE4-4,WIDE5-5,WIDE6-6,WIDE7-7
10.Unproto : APN391 VIA WIDE
11.Monitor : OFF
12.Cmsg : DISC
13.Ctext : REMOTE WX / APRS STATION @ DM70xv , BYE!
14.Btext : MT.McELROY / TX/ APRS WEATHER @ 6654FT. / DM70xv
15.Beacon E 20
16. Blt 1 E 00:30:00 START 00:00:00
17. Blt 2 E 00:30:00 START 00:00:15 CLEAR
18. Blt 3 E 00:30:00 START 00:15:00
19. Blt 4 E 00:30:00 START 00:15:20 CLEAR
20.Lt 1 !3054.55N/10403.82W_PHG6860/A=006654ft / MCP/W4/ HIGHEST APRS IN
TX / MT.McELROY / DM70xv/ 1
21.Lt 2 [leave blank--wx
/(128 chrs.)]
22.Lt 3 !3054.55N/10403.82W_PHG6860/DM70xv/ W4/ TNX WTC,INC + INTERTIE,INC.
/ DM70vx/3
23.Lt 4 [leave blank--wx
/(up to128 chrs.)]
24.Ltp 1 APN391 VIA WIDE3-3
25.Ltp 2 APN391 VIA WIDE2-2
26.Ltp 3 APN391 VIA WIDE2-2
27.Ltp 4 APN391 VIA WIDE3-3
28.Gpshead 2 @
29.Gpshead 4 @
31.Rtext : xxxxxxxx [ keep private ]
30.Myremote : xxxxxxx like
'W5EX-15' [keep private(call sign)]
32.Txdelay :27 [270ms]
33.Sl 8
[slottime = 80ms]
34.Int GPS
After the above command [ # 34 ] you must turn off the tnc or
send ‘reset’ to make it go into the GPS mode which the weather station
uses. The tnc Db-25 is now the Davis
weather input. Assemble your Davis weather station and check to make sure it
works. Then shut it down and plug in the "data logger" in the back of
the weather display. It takes a bit of pressure to put it in. Then insert '3'
c-cells [battery back up ] in the back
of the display and connect the weather station to the AC. DO NOT PLUG THE LOGGER IN WITH ANY POWER ON OR YOU
WILL BE BUYING A NEW ONE !. Connect the RJ-45 from the logger to a Db-9
adapter [Davis supplied] into your computer com port (1). Load the software up
[ Weather Link 5.5.1 ] and run "setup comport". Set
the baud rate at 9600 to match the tnc
[9600]. Then run "config streaming data logger" and
answer all the questions. Then take the RJ-45 and plug it into the [Davis
supplied] Db-25 adapter and into the
KPC3+ / Db-25. You should be up and
running! Also, this setup will run as a digi / weather station / and with the
new Paradigm W-4 [ with the above setup ].
KP3+ Extra
Aux. Input / outputs
Remote KPC3+ AUX. INPUT / OUTPUTS with its own beacon!
1.[ Input ] 0-5v, An0 [ J8, pin 1 ] goes to P1 [radio port] pin 4. Sw to db-25, pin 18 / J8, #2
2.[ Input ] 0-5v, An1 [ J10, pin 1 ] goes to P1 [ radio port ] pin 8. Sw
to db-25, pin 11 / J10, #2
A [ output ] pin 4 on='ctrl A on',
off = 'ctrl A off'. A & b
can be pulsed too.
B [ output ] pin 8 on='ctrl B off', off = 'ctrl B off'.
Telemetry
'TEn' = [ n x 10 sec ] to
beacon, i.e., [ 'TE1200' = beacon every 20 min.]
Read analog 0
= 'An0' Use 'myremote' command then
send 'an0' .
Read analog 1 = 'An1'
More input / outputs on the KPC3+ [ normally only 2 hook ups] can be
made by hand wiring more off the KPC3+
circuit board.
Range*
Range command=Ra 0-255 / i.e.,
0-255 range for # '0' with a 12 vdc scale = 'Ra 0-12'
Remember no voltage over 5 vdc , so use a voltage
divider !
Two things that will be used above
will be to monitor battery [ back up ] voltage on the station and shack
door open/closed.
73,
Dink, WA5LNL
Revised: 12/05/04 08:30 PM by N5VRP, Dennis Rogers, Webmaster
Copyright 2006 by Intertie, Inc. All Rights Reserved
No use of these symbols or phrases is allowed without the express written
permission of Intertie, Inc.
![]()